This article takes an in-depth look at rubber gaskets.
Read further to find out more about topics such as:
Rubber gaskets are versatile components crafted to seal the small gaps between two connected surfaces or joints. They are commonly used in various applications, such as sealing flange faces within piping systems, cylinder heads in vehicles, engine blocks, tank rims, covers, as well as door edges and frames. These gaskets operate by adjusting and fitting into the discrepancies of the hard surfaces they come in contact with. The sealing function is accomplished as the components compress the gasket, causing it to deform and establish a robust seal.
The superior sealing capability of rubber stems from its elastomeric nature. Both natural and synthetic rubbers belong to the elastomer family, which are polymers distinguished by their exceptional elasticity. This flexibility emerges from the cross-linking of lengthy polymer chains into amorphous formations. The moderately weak intermolecular forces present among these chains allow them to adapt when subjected to stress. This adaptability permits elastomeric gaskets to conform to a variety of surface profiles, guaranteeing a reliable seal.
Rubber gaskets provide numerous advantages over metallic and other non-metallic gaskets due to their distinctive properties. Their exceptional elasticity, or ability to deform and recover to their original shape, is essential for creating leak-proof, long-lasting seals in a wide variety of applications. Additionally, rubber gaskets are easier to manufacture and can be customized from a diverse selection of raw elastomeric materials. Whether used for industrial, automotive, plumbing, or high-purity applications, the unique characteristics of rubber gaskets make them a preferred sealing solution. Below are some of the key benefits and reasons why rubber gaskets are chosen in critical sealing environments.
Rubber gaskets are produced by blending raw rubber compounds with various additives and forming them into the desired shapes. Both thermosetting and thermoplastic rubbers exhibit excellent processability and formability. In their liquid or uncured state, rubber flows smoothly into intricate molds and dies, allowing for high-precision gasket manufacturing through compression molding, transfer molding, and injection molding processes. After curing, the rubber material can be efficiently cut, stamped, or machined into custom gasket shapes for specific applications.
Compared to metallic and other non-metallic gaskets, producing rubber gaskets requires lower heat and pressure, resulting in reduced tooling costs, lower energy consumption, and decreased overall production expenses. This makes rubber gaskets an economical choice for high-volume production and custom prototyping. Industries benefit from the scalability and flexibility of rubber gasket manufacturing, enabling fast turnaround times and cost savings on replacement parts and maintenance.
The unique viscoelastic and elastic properties of rubber allow these gaskets to stretch, compress, and return to form without damage or permanent deformation. This natural flexibility lets rubber gaskets conform to uneven or rough sealing surfaces, filling micro-irregularities and creating highly reliable seals. Such adaptability is critical in preventing leaks of liquids, gases, oils, or chemicals.
Compared to metal gaskets, which rely primarily on physical compression and surface roughness for a labyrinth seal, rubber gaskets can create uniform sealing forces with lower bolt torque and less hardware stress. Their ability to maintain sealing integrity under thermal cycling and vibration provides added protection in demanding environments, including high-pressure, high-temperature, and aggressive chemical service. By minimizing the risk of seal failure, rubber gaskets reduce downtime and improve the safety and efficiency of industrial equipment.
Unlike many other gasket types, rubber gaskets can be engineered using a broad spectrum of base polymers and formulations to address highly specific sealing requirements. Common rubber gasket materials include natural rubber, silicone, EPDM (ethylene propylene diene monomer), neoprene, nitrile (NBR or Buna-N), Viton (FKM), polyurethane, butyl, and SBR (styrene butadiene rubber). By adjusting the base elastomer and introducing performance additives, manufacturers can tailor properties such as temperature resistance, chemical compatibility, weatherability, and mechanical strength.
This versatility is further enhanced by the design flexibility offered by modern rubber compounding techniques. Additives such as stabilizers, fillers, antioxidants, UV inhibitors, and reinforcements allow for the production of countless patented and proprietary engineered rubber gasket materials. These materials are formulated to address the unique sealing demands of industries such as oil and gas, water treatment, food processing, and pharmaceuticals.
While metallic gaskets are usually restricted to materials like stainless steel, and mineral gaskets are typically made from mica or vermiculite, rubber gaskets stand out for their adaptable material profiles. The only comparable gasket type is the compressed fiber gasket, which also incorporates elastomeric components along with fibers.
When specified correctly, rubber gaskets offer outstanding durability and resistance to a wide range of corrosive chemicals and harsh environmental conditions. This chemical resistance is dependent upon both the base polymer and the specific additives used in the rubber compound. For example, fluorocarbon elastomers like FKM (Viton) and PTFE gaskets are renowned for their exceptional resistance to strong acids, fuels, hydrocarbons, and extreme temperatures. Other popular materials, such as SBR, butyl, neoprene, and EPDM, provide excellent aging and weatherability, making them ideal for exposure to ozone, UV, water, and oxidizing agents.
Industry professionals often turn to specialized rubber gasket materials for critical applications such as chemical processing, water treatment, automotive fuel systems, hydraulic sealing, and HVAC systems. Selecting the right rubber compound ensures maximum service life and minimizes maintenance due to chemical degradation.
Rubber gaskets are valued for their extensive range of customizable physical properties. Through precise formulation and compounding, characteristics such as durometer (hardness), compression set, compressive modulus, tensile strength, elongation at break, and low-temperature flexibility can be optimized for specific operating environments. This ability to fine-tune gasket performance is crucial when balancing requirements for sealing tightness, resistance to extrusion, pressure containment, and mechanical wear.
For example, a softer gasket material may be preferred for fine sealing at low pressures or fragile flanges, whereas harder rubber compounds are selected for high-pressure, high-load, or chemically aggressive applications. Premium engineered rubber gaskets maintain excellent resiliency and sealing performance, even under fluctuating loads and repeated assembly/disassembly in flanged connections and piping systems.
Rubber gaskets lend themselves to a wide range of fabrication methods and custom shapes. Large sheets of gasket material can be supplied for further cutting and processing, enabling fabricators and maintenance teams to create custom gasket profiles for irregular flanges, piping joints, or specialty equipment. Common fabrication methods include hand-cutting, die cutting, water-jet cutting, and laser cutting. Laser cutting is particularly effective for producing precise, repeatable gasket shapes with intricate geometries.
Beyond cutting, extrusion and injection molding allow for the production of complex, seamless rubber gasket profiles for high-volume applications such as door seals, window gaskets, and o-rings. These elastomer forming techniques use CAD-assisted tool and die manufacturing to produce tooling that matches the required mating surface geometry exactly, ensuring consistent profile integrity and repeatability in finished gaskets.
Custom gasket fabrication meets the needs of diverse industries, from automotive and aerospace to marine, plumbing, and electronics, where reliable sealing is critical to system safety and performance.
Rubber compounds can be specially engineered to meet stringent FDA and NSF standards for food, beverage, pharmaceutical, and potable water applications. Food-grade rubbers such as nitrile (NBR), neoprene, silicone, EPDM, and FKM are formulated with only approved ingredients to ensure they do not leach harmful substances into the end product. These rubbers also demonstrate resistance to bacterial growth, are easy to sanitize, and retain their performance under exposure to cleaning agents, oils, and a wide range of temperatures.
Choosing FDA-compliant rubber gasket materials is essential for industries that require strict hygiene, odor-free operation, and regulatory compliance. Food processing plants, commercial kitchens, laboratory equipment, and pharmaceutical manufacturers all rely on silicone and EPDM gaskets for their non-reactivity, cleanliness, and durability. In addition, food-safe rubber gaskets provide leak-free sealing for mixers, pumps, tanks, and pipelines handling consumables and sensitive products.
One of the often-overlooked advantages of rubber gaskets is their extended service life and the maintenance savings they provide. Due to their resilience, resistance to permanent deformation, and ability to withstand repeated compression, high-quality rubber gaskets often outlast alternatives in dynamic and static sealing applications. Their non-corrosive nature means they are less likely to seize or bond to flanges, enabling easier removal and replacement during scheduled maintenance or equipment repairs.
This longevity and ease of use reduce operational downtime while supporting cost-effective maintenance schedules across a range of industries, including chemical processing, power generation, and water treatment facilities.
Rubber gaskets are indispensable components in a broad range of industrial sectors, celebrated for their exceptional sealing capabilities, flexibility, and resistance to harsh environments. Their versatility allows them to perform reliably in both standard and highly specialized settings, making them a top choice for sealing applications involving liquids, gases, and chemicals. Due to their unique physical and chemical properties, rubber gaskets provide efficient sealing performance in industries such as oil and gas, water treatment, automotive manufacturing, aerospace, marine, food processing, chemical processing, and pharmaceuticals. Their primary strengths include resisting chemical attacks, tolerating varying temperatures and pressures, and providing lasting durability against mechanical stress and environmental exposure.
Explore the most common industrial uses for rubber gaskets below, along with examples of suitable gasket materials and properties based on specific operational demands.
Rubber gaskets are a staple in industrial piping systems and pipe fitting assemblies due to their ability to deliver leak-proof seals and withstand fluctuating pressure and temperature conditions. In industries such as chemical processing, oil refining, and water distribution, rubber gaskets help maintain system integrity by preventing leakage of corrosive fluids, toxic gases, or high-pressure steam. Gaskets made from EPDM, nitrile (NBR), or neoprene rubbers are selected for their compatibility and resistance to specific chemicals and abrasion. Most standard rubber gaskets are rated for pressures up to 150 psi (10 bars), while specialized varieties—such as PTFE (polytetrafluoroethylene) composite gaskets—are engineered for high-pressure service, up to 800 psi (55 bars).
In water utility and plumbing systems, rubber gaskets play a vital role in creating watertight seals throughout residential, commercial, and municipal water networks. Their affordability, non-reactive nature, and resistance to corrosion, chlorine, and biological growth make them ideal for faucets, drains, toilets, pipe joints, pumps, and water filtration components. Common materials include silicone and EPDM rubber gaskets, known for their longevity in potable water applications and compliance with drinking water safety standards. Choosing the proper gasket type enhances efficiency, minimizes maintenance, and extends the service lifespan of plumbing systems.
The automotive industry relies heavily on rubber gaskets for both critical and non-critical sealing tasks. Applications include:
With advancements in electric vehicles and hybrid technologies, rubber gasket materials are also evolving to meet the demands for battery enclosure sealing, high-voltage insulation, and thermal management in next-generation automotive systems.
Rubber gaskets in aerospace applications serve critical safety and performance functions. They are installed in fuel delivery systems, hydraulic circuits, engine housings, and electronic enclosures, where exposure to extreme temperatures, high pressure, and intense vibration is common. Precision-engineered, aerospace-grade gaskets are often fabricated from advanced elastomers with flame-retardant, anti-static, or conductive properties to protect sensitive avionics and reduce risks associated with fire or electromagnetic interference. EMI (Electromagnetic Interference) shielding gaskets are specifically designed to comply with stringent aerospace standards, safeguarding instruments against voltage surges and stray currents. Rubber gaskets contribute to enhanced reliability, reduced maintenance costs, and improved in-flight safety.
Durable rubber gaskets are integral to marine equipment and shipbuilding, providing secure barriers against water intrusion and saltwater corrosion. They are used to seal hatches, watertight doors, portholes, windows, and hull penetrations, ensuring vessel integrity even under heavy impact, vibration, or compressive loads. High-performance marine-grade rubbers such as EPDM and neoprene offer exceptional weathering, ozone, and UV resistance, making them dependable in harsh ocean environments. Choosing the right gasket for marine environments also helps maintain structural safety and prolongs the operational life of vessels and offshore installations.
Rubber gaskets are widely adopted to seal access covers, manways, inspection ports, nozzles, and flanged connections in storage tanks, silos, and containers handling liquids (e.g., chemicals, fuels, water) or bulk solids. Key advantages include reliable sealing performance, cost-effectiveness, and a broad spectrum of resistance properties. For specific needs:
Proper gasket selection is essential for maintaining leak-free operation, complying with safety regulations, and minimizing contamination risks, especially in industries with hazardous or sensitive materials.
Food, beverage, and pharmaceutical manufacturers depend on hygienic and FDA-compliant rubber gaskets for critical sealing in processing, packaging, and fluid transfer systems. These gaskets are formulated from non-toxic, tasteless, and odorless compounds such as silicone and EPDM, complying with stringent regulatory standards for contact with consumables. Applications include:
Optimal gasket materials are selected for resistance to harsh cleaning chemicals (CIP/SIP), steam sterilization, and degradation by acids, sugars, or alcohols commonly found in food and pharmaceutical processes. Proper installation and regular inspection of rubber gaskets contribute to product purity, safety, and process reliability.
As industry standards and processing technologies evolve, manufacturers increasingly seek custom rubber gasket solutions with enhanced chemical resistance, temperature stability, and documentation for regulatory compliance—reinforcing the importance of working with experienced gasket specialists to ensure the right fit for every application.
Rubbers are typically categorized based on the monomers used to create their polymer chains. These monomers can include hydrocarbons like ethylene, methylene, propylene, isoprene, and fluorocarbons. The structure of the polymer chain defines the fundamental properties of the rubber. Additional components such as curatives and additives further modify these properties, leading to various subclassifications within the main rubber types.
Here are some of the most commonly used rubber gasket materials available on the market.
Ethylene propylene diene monomer (EPDM) is an elastomer created through the copolymerization of ethylene and propylene. It offers excellent weather resistance, as well as strong insulating and dielectric properties. EPDM performs well mechanically across a broad temperature range, both high and low. Chemically, it resists acids, alkalis, alcohols, and ketone-based solvents, and it provides adequate resistance to water and steam.
Nitrile rubber, also known as acrylonitrile butadiene rubber (NBR), is produced by copolymerizing acrylonitrile and butadiene. It is commonly used for its resistance to fuels, oils, and petroleum-based solvents, making it ideal for sealing automotive engine components. However, nitrile rubber has relatively lower mechanical properties and performs poorly at low temperatures compared to other rubber materials. To address these limitations, reinforcing fillers are often added.
Neoprene, also known as chloroprene rubber (CR), is synthesized through the emulsion polymerization of chloroprene. It is renowned for its flame-retardant properties. The chlorine content in its polymer chain enhances its resistance to oxidation, ozone, and oil, though its oil resistance range is not as extensive as that of nitrile rubbers. Additionally, neoprene tends to be more costly than natural rubber and exhibits poor performance at low temperatures.
Natural rubber is derived from the latex of the Hevea tree and consists primarily of the polymer chain polyisoprene. It is recognized for its resilience and resistance to fatigue. However, its performance can often be outmatched by synthetic rubber types. Additionally, natural rubber gaskets generally have limited resistance to ozone and oil.
Silicone rubbers feature a silicon-oxygen backbone rather than a carbon-based structure. They are known for their excellent resistance to oxygen, ozone, heat, light, and moisture. Despite these advantages, silicone rubbers tend to be more costly and offer only moderate mechanical properties compared to organic (carbon-based) rubbers. Additionally, they have limited resistance to petroleum-based chemicals.
Butyl rubber (IIR) is a copolymer of isobutylene and isoprene, with the isoprene content carefully controlled to achieve the desired level of unsaturation. Its low unsaturation makes butyl rubber highly resistant to most chemicals, both gaseous and liquid, and it exhibits exceptional aging resistance when properly vulcanized. Due to its superior impermeability, butyl rubber is commonly used in seals for equipment handling compressed air and process gases.
Styrene-butadiene rubber (SBR) is produced through the emulsion polymerization of styrene and butadiene, and is commonly known as red rubber in commercial blends. As a general-purpose rubber, SBR rivals natural rubber in terms of tear, abrasion, and thermal resistance properties. Due to its lower cost, SBR gaskets are often favored over natural rubber options.
Santoprene is a proprietary gasket material classified as a thermoplastic vulcanizate (TPV) or thermoplastic elastomer (TPE). It consists of dynamically vulcanized EPDM dispersed within a polypropylene matrix. Its thermoplastic nature allows it to be melted and recycled. Santoprene offers strong resistance to degradation from ultraviolet light and ozone. This trademarked material is currently owned by ExxonMobil.
Polyurethane, commonly known as urethane, is created by reacting polyether or polyester glycols with diisocyanates and curing agents. It is a versatile material appreciated for its wide range of physical properties, which can be tailored through various formulations. Polyurethane is known for its exceptional resilience, abrasion resistance, and weathering durability.
Poron is a patented gasket material composed of multicellular polyurethane or polyurethane foam. Its porous structure makes it ideal for applications requiring thermal insulation, vibration and acoustic damping, and shock absorption. The resilience and rebound characteristics of polyurethane contribute to its effectiveness in sealing applications by minimizing creep relaxation.
FKM, or fluorocarbon rubber, is a type of rubber made from the copolymerization of vinylidene fluoride (VDF) with other chemicals like hexafluoropropylene (HFP) and tetrafluoroethylene (TFE). Commercially, it is known under the trade name Viton. Viton gaskets are high-performance and relatively expensive, designed for use in demanding environments such as automotive and aerospace applications. They excel in high-temperature conditions and are resistant to oils, fuels, acids, and alkalis.
Although it is technically a plastic, PTFE is widely used as a gasket material in chemical processing due to its exceptional bonding energy. This property grants PTFE remarkable resistance to chemical reactions and corrosion. Additionally, PTFE features a low coefficient of friction, outstanding insulating capabilities, high toughness, and good impact resistance.
Rubber gaskets can be manufactured through various processes, each affecting the quality, precision, and characteristics of the final product. These methods come with their own sets of advantages and limitations. Below, you will find an overview of some of these manufacturing processes.
Die-cutting is a bulk manufacturing technique where shapes are cut from flat stock material using a tool known as a die. This die is a specialized tool with the product's two-dimensional profile and features a sharp edge, often referred to as the steel rule. The cutting process involves pressing the die into the material on the machine’s bed, with a single downward motion shearing the material into the desired shape.
Die-cutting is a favored method for producing rubber gaskets due to its straightforward process, cost-effective tooling, minimal material waste, and high production efficiency. This technique is commonly employed for gaskets used in general applications like plumbing and container sealing.
Water jet cutting is a non-conventional method that utilizes a high-velocity stream of water to cut various materials, including rubber. The process involves pumping water at extremely high pressures through a small nozzle, converting fluid pressure into a high-speed jet. This powerful jet cuts through the material by impingement and erosion.
Water jet cutting is ideal for fabricating gaskets that are sensitive to pressure and temperature, as it minimizes stress on the material and avoids burning the edges. However, a key limitation is that the stock material must be resistant to water to prevent degradation during the cutting process.
Laser cutting is a non-conventional technology that employs a highly concentrated beam of light, known as a laser, to cut materials. The laser beam is directed along the cutting lines, causing the material to rapidly vaporize or sublimate at the exposed areas, resulting in precise cuts.
Laser cutting is favored for its precision and clean cutting process. Unlike water jet cutting, it does not involve wetting the product, which avoids issues like swelling and degradation. Additionally, laser cutting equipment typically requires less maintenance compared to water jet cutting machinery.
Flush cutting is a mechanical process that utilizes a small, oscillating knife to cut through soft and semi-rigid materials like rubber. The knife is mounted on a robotic system and controlled by a CNC program, allowing for precise and automated cutting.
Flush cutting is a precision technology similar to water jet and laser cutting. It offers the advantage of not subjecting the material to pressure, high temperatures, or water. However, it is less effective for cutting harder materials.
Injection molding is primarily a plastic forming process but can also be used for molding rubber. In this process, the rubber is first melted to a manageable viscosity or, in the case of liquid uncured rubbers, directly injected. The molten rubber is then injected into a mold, which has a negative image of the final product. Inside the mold, the rubber solidifies, cures, and cools. After the hardening phase, the molded rubber gasket is released.
Injection molding is especially useful for producing rubber gaskets with rounded or complex three-dimensional shapes, such as O-rings. Unlike cutting methods, which are limited to flat profiles, injection molding allows for the creation of gaskets with intricate geometries and detailed designs.
The process of rubber gasket extrusion involves pushing a rubber compound through a specialized die to create gaskets with the desired cross-sectional shape. This method is versatile and can be used with different types of rubber, such as EPDM, silicone, neoprene, Viton, and natural rubber.
Extrusion starts by introducing the rubber compound into a hopper, which is designed to funnel the material into the extrusion barrel. Modern systems often feature automated hoppers for efficient material handling.
During extrusion, a helical screw inside the barrel moves the rubber compound forward, while heating elements warm the material to make it more flexible. The rubber is subjected to increasing pressure and temperature as it progresses towards the die. Once the rubber exits the die, it may expand or swell depending on the hardness of the material and the formulation used.
Once the rubber exits the extrusion die, it undergoes vulcanization to achieve the required tensile strength. This curing process involves heating the rubber and can be accomplished through methods such as steam curing, continuous curing, or by cutting the rubber to specific lengths. Vulcanization is a chemical process that typically uses sulfur to cross-link the rubber molecules. During this stage, the rubber may expand or contract in both its cross-sectional area and length, depending on the formulation of the rubber compound.
Vulcanization is a chemical treatment that enhances the physical characteristics of rubber. This process boosts the rubber's tensile strength and its resistance to swelling and wear. It primarily involves heating rubber in the presence of sulfur.
The vulcanization technique was pioneered by Charles Goodyear during the early stages of the industrial revolution. He found that using an accelerator could speed up the vulcanization process at lower temperatures. Sulfur plays a crucial role in this process by chemically bonding with rubber to create cross-links between the long molecular chains.
Steam curing is suitable for small quantities of extruded rubber and is considered a safe vulcanization method. Rubber subjected to steam curing exhibits excellent durability, making it particularly effective for gaskets used in bonding applications.
Continuous curing is used for processing larger quantities or sizes of gaskets. This method employs microwaves or a salt bath to gradually cure rubber. It is energy-efficient and produces rubber gaskets with more uniform profiles.
Hot splicing involves using heat, pressure, and a splicing film made of polyethylene to join the ends of rubber profiles, creating tightly bonded gaskets. The heat used can be conventional or infrared, which helps bond the polyethylene film. Hot splicing achieves stronger molecular bonds compared to traditional vulcanization. This technique is suitable for gaskets cut by water jet to ensure clean and precise edges.
Numerous machines are designed for the production of rubber gaskets, playing a crucial role in modern manufacturing. These machines ensure the efficient and accurate creation of sealing components for diverse industries, including automotive, aerospace, and marine sectors. They are essential for producing reliable seals that prevent leaks and maintain operational integrity. Below, we highlight several prominent brands recognized for their expertise in supplying machinery for rubber gasket production:
Atom FlashCut provides the FlashCut Gasket Cutting System, renowned for its high precision in cutting, adaptable software, and capability to work with a range of rubber materials for gasket manufacturing. Its effectiveness, accuracy, and versatility make it a preferred choice in the industry.
Dieffenbacher is known for its Fiberforge machine, which integrates extrusion and lamination techniques to create rubber gaskets with continuous lengths and tailored profiles. This advanced method ensures outstanding sealing performance and high-quality results, contributing to its widespread use in the industry.
Zemat Technology Group offers the Zemat RCE Gasket Cutting Machine, renowned for its rapid cutting speed and precise performance in the production of rubber gaskets. Its effectiveness and dependability have made it a favored choice in the industry.
Sutherland Presses focuses on compression molding presses designed specifically for gaskets, including those for rubber. These machines provide accurate control over temperature, pressure, and molding duration, which guarantees uniform quality and effective sealing properties. Their dependability and high-quality results contribute to their widespread use in the industry.
Rolmacon Global Ltd is known for the Rolmacon Gasket Die Cutting Machine, which excels in delivering precise and efficient die cutting for rubber gaskets. The machine's speed, precision, and capability to accommodate various gasket designs have made it a favored choice in the industry.
Keep in mind that the details regarding specific models, features, or components may have changed since this update. For the latest information, it is advisable to reach out to the manufacturers directly or consult current industry resources for updates on machines used in rubber gasket production in the United States and Canada.
Gaskets are a type of mechanical seal that inhibits leakage by filling the gap between static mating surfaces. It takes advantage of the compressive force that drives the gasket material to plastically flow between the...
Gaskets are seals that are mechanically made to prevent either process fluids from escaping or contaminants from entering the delicate areas. Each given system has its best suited gasket, and it is critical to make the right...
The head gasket is a motor engine component that seals the combustion part of the engine so that oil and the motor coolant circulate. The head gasket also seals the combustion chamber inside the engine...
Molding is a manufacturing process that uses a mold - the latter being a solid container used to give shape to a piece of material. It is a forming process. The form is transferred from the mold to the material by...
Die cutting is the mass fabrication of cut-out shapes by shearing a stock material such as paper and chipboard using tooling called a die. A die is a specialized tool used in manufacturing to cut or shape a material fitted into a press...
Hydraulic seals are a form of gasket-like rings that are used to fill gaps between hydraulic cylinder components. Many different components are found in hydraulic cylinders, some of which get in...
Kiss cutting is a method for cutting into a material where the upper layers are pierced, but the back layer is left intact. The term "kiss" refers to the way the blade touches the upper layers of the material and leaves a pattern...
An O-ring is a round elastic loop that is used as a seal for static and dynamic applications. Their main purpose is to serve as a seal between structures such as pipes, tubes, in pistons, and cylinders. O-rings are made of...
Rubber injection molding is when uncured rubber is transformed into a usable product by injecting raw rubber material into a mold cavity made of metal. The applied pressure produces a chemical reaction like...
Rubber molding is a process of transforming uncured rubber or an elastomer into a usable product by transferring, compressing, or injecting raw rubber material into a metal mold cavity...
A rubber O ring is a mechanical gasket in the shape of a torus or donut and is used for static and dynamic applications where there is relative motion between parts and the possibility of friction. Some of the benefits of rubber O rings are...
There are several methods to perform rubber overmolding, and each method has its own unique advantages and disadvantages. The choice of method typically depends on the design and material requirements of the product being...
Silicone rubber molding is a method for shaping, forming, and fabricating silicone rubber parts and products using a heated mold. The process involves compressing or injecting silicone rubber into a mold...
A grommet edging is a flexible rubber or plastic strip that covers rough and sharp surfaces found in openings and edges of panel walls to protect the passing electrical cables, wires, and other sensitive components...